Un riepilogo di ciò che si è mosso a livello ISO nel secondo semestre dell’anno (evidenziati i documenti più rilevanti).
Nuovi documenti tecnici pubblicati:
- ISO 23225:2025 Nuclear Power Plants Corrosion Control Engineering Life Cycle — General Requirements
- ISO 11124-6:2025 Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 6: Stainless steel (shot and irregulars)
- ISO 24251-1:2025 Prevention of hydrogen assisted brittle fracture of high-strength steel components — Part 1: Fundamentals and measures
- ISO/PAS 5929:2025 Corrosion of Metals and Alloys — Test and evaluation method for the corrosion of steel bar embedded in concrete structure exposed to total corrosion zones in marine environments
- ISO 5872:2025 Oil and gas industries including lower carbon energy — Pipeline transportation systems — Terms and definitions
- ISO 9350:2025 Corrosion of Metals and Alloys — Testing method for corrosion resistance for hafnium in the high temperature and pressure
- ISO 10903:2025 Oil and gas industries including low carbon energy— Pipeline transportation systems—Pipeline geohazard monitoring processes, systems and technologies
- ISO/TR 22861:2025 Guidelines of marine environment zonation for steel corrosion embedded in concrete
- ISO 12994:2025 Electrodeposited nickel plus chromium coatings for automobile plastic parts－specification and test requirements
- ISO/TS 9124:2025 Paints and varnishes — Thermal performance of paint films — Determination of solar irradiation penetration ratio with heat flow meter
Norme modificate:
- ISO 11126-1:2025 Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 1: General introduction and classification
- ISO 11125-5:2025 Preparation of steel substrates before application of paints and related products — Test methods for metallic blast-cleaning abrasives — Part 5: Determination of percentage defective particles and of microstructure
- ISO 8501-3 Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 3: Preparation grades of welds, edges and other areas with surface imperfections
- ISO 11997-2:2025 Paints and varnishes — Determination of resistance to cyclic corrosion conditions — Part 2: Wet (salt fog)/dry/humidity/UV light
- ISO 11126-10:2025 Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 10: Almandite garnet
- ISO 2081:2025 Metallic and other inorganic coatings — Electroplated coatings of zinc with supplementary treatments on iron or steel
Nuovi documenti tecnici arrivati alla fase di approvazione finale:
- ISO/FDIS 18971 Corrosion of metals and alloys — Monitoring method for corrosion states of stainless steel in industrial cooling water
- ISO/FDIS 25018 Corrosion of metals and alloys — Determination of resistance to stress corrosion cracking of copper and copper-zinc alloys in ammonia vapour
- ISO/DTR 5503 Preparation of steel substrates before application of paints and related products — Non-visible residues after surface preparation with single use abrasives
- ISO/FDIS 21055 Corrosion of metals and alloys — Test method for microbiologically influenced corrosion of oil and gas transmission pipelines
- ISO/DTR 22801 Corrosion of metals and alloys – Testing methods for corrosion of conducting alloys in AC electric current condition
Revisioni di documenti tecnici arrivate alla fase di approvazione finale:
- ISO/FDIS 21809-4 Oil and gas industries including lower carbon energy — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 4: Polyethylene coatings (2-layer PE)
- ISO/DTS 19392-6 Paints and varnishes — Coating systems for wind-turbine rotor blades — Part 6: Determination and evaluation of ice adhesion using centrifuge
- ISO/FDIS 21809-2 Oil and gas industries including lower carbon energy — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 2: Single layer fusion-bonded epoxy coatings
- ISO/FDIS 29601 Paints and varnishes — Corrosion protection by protective paint systems — Assessment of porosity in a dry film
- ISO/FDIS 15589-1 Oil and gas industries including lower carbon energy — Cathodic protection of pipeline systems — Part 1: On-land pipelines
- ISO/FDIS 14993 Corrosion of metals and alloys — Accelerated testing involving cyclic exposure to salt mist, dry and wet conditions
Nuovi documenti tecnici arrivati alla fase di approvazione tecnica finale:
- ISO/DIS 16364 Guidelines for Galvanic Corrosion Control
- ISO/DIS 25072 Corrosion of metals and alloys — Guidelines for drawing regional corrosion map — Detailed measurements of corrosion and interpolation method
- ISO/DIS 25014 Paints and varnishes — Coatings on concrete — Determination of film thickness on cross section
- ISO/DIS 8502-16 Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 16: Extraction of water soluble contaminants for analysis, the saturated filter paper method
Revisioni di documenti tecnici arrivate alla fase di approvazione tecnica finale:
- ISO/DIS 11997-1 Paints and varnishes — Determination of resistance to cyclic corrosion conditions — Part 1: Wet (salt fog)/dry/humid
- ISO/DIS 12490 Oil and gas industries including lower carbon energy — Mechanical integrity and sizing of actuators and mounting kits for pipeline valves
- ISO/DIS 21809-3 Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 3: Field joint coatings
- ISO/DIS 11998 Paints and varnishes — Determination of wet-scrub resistance of coatings
- ISO/DIS 1456 Metallic and other inorganic coatings — Electrodeposited coatings of nickel, nickel plus chromium, copper plus nickel and of copper plus nickel plus chromium
- ISO/DIS 11177 Vitreous and porcelain enamels — Inside and outside enamelled valves and pressure pipe fittings for untreated and potable water supply — Quality requirements and testing
- ISO/DIS 11124-1 Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 1: General introduction and classification
- ISO/DIS 8501-1 Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
- ISO/DIS 16440 Oil and gas industries including lower carbon energy — Pipeline transportation systems — Design, construction and maintenance of steel cased pipelines
Numero di bozze in votazione: 23, di cui 10 revisioni
Numero documenti in bozza: 19, di cui 13 revisioni
Numero di nuove proposte: 31